AMF S-311 Manuel de service télécharger pdf (Page 16)

S-311

e-mail: service@amfreece.cz; parts@amfreece.cz; website: www.amfreece.com

Phones: +420 582 309 146 (Service); +420 582 309 286 (Spare Parts); Fax: +420 582 360 606

Revised 03/2006

1-4

A - INTRODUCTION

4. SPECIFICATION

* Note: If a customer uses thread size 100 and less, the manufacturer recommends to use the left looper 17.0069.4.019

If you use poor quality threads on the machine, the thread can burn at the needle (producer recommend

decrease machine´s speed).

S-3

Elektroni

c b

uttonhole machi

ne wi

th chai

n sti

tch i

s possible to use for men`s and w

omen`s wear

Possible to use gi

mp thread, not i

n round e

ye.

Machine type/model

10 to 50 mm

3,0 - 20,0 mm

4 to 8 mm

4 to 20

12 mm

in 8,0 mm

Cut before (CB), cut after (CA), no cut (OFF)

- 0,50 to + 1,2 mm

See section D 3.3

4 to 6 mm

0,5 to 1,5 mm

No eye; 2,2 x 3,0 mm; 2,8 x 4,2 mm; 3,0 x 4,6 mm; 3,2 x 5,0 mm; 3,4 x 4,2 mm

2,1 mm (± 0,3 mm electronic); 2,7 mm ( ± 0,3 mm electronic)

± 1,5 mm

64 mm

02.0558.0.111 (Nm 100)

02.0558.1.112 (Nm 110)

80, 100, 120, gimp size 30.

L = 16 to 20 mm

L+L = 23 to 27 mm

L = 20 to 24 mm

L+L

= 27 to 31 mm

0,55 MPa = 80 PSI

530 mm (height) x 370 mm (width) x 560 mm (depth)

730 mm (height) x 1100 mm (width) x 700 mm depth) + 150 mm distance

64 kg

175 kg

1NPE~60Hz 230 V/TN/S; 1NPE~50Hz 230 V/TN/S

Min. 10A Characteristic C (EN60947-2)

L =86,9db; L =74,8 db; Noise measurement according to EN ISO 3746:1995

wA pfA

L = 24 to 28 mm

L+L

= 31 to 35 mm

according to IEC 364-3, IEC 364-5-51 temperature from +5°C to 40°C, relative air humidity from 30 to 8 0%

L = 28 to 32 mm

L+L

= 35 to 39 mm

16 to 20 mm 20 to 24 mm 24 to 28 mm 28 to 32 mm

1000 to 2000 stitches/min (500 to 1000 rev/min of the drive shaft)

0,5 to 2,0 mm (increments of 0,1 mm)

Sewing speed

Stitch Density

Buttonhole style

Eye type

Flybar length

Length of the cross bar

Number of stitches in the eye

Number of stitches in the round end

Clamp foot height (max)

Maximum work thickness

Buttonhole Cutting Mode

Cutting Space

Cut position (Y axis)

Bedplate movement

Needle system

Recommended threads*

Upper thread trimming

Lower thread and gimp trimming

Cutting space

Operating Condition

Air pressure

Machine db Level

Machine Head Dimension

Machine Head Weight

Table Dimensions

Machine Weight

Electrical requirements

Line Circuit Breaker

Bite Range Elecctronic

The length

of hole

CT 16 - 20 mm CT 20 - 24 mm CT 24 - 28 mm CT 28 - 32 mm

L = 3 to 7 mm

(Short ends)

max 3,5 mm

0,5 to 1,5 mm

Cross bar density

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 103 104

Commentaires sur ces manuels

Pas de commentaire

AMF S-311 Manuel de service Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Machines à coudre AMF S-311